How To Fix Kenmore Ice Maker?

How do I reset my Kenmore ice maker?

How to Reset a Kenmore Ice Maker

  • Locate the cover plate on the front of the Kenmore ice maker, and pull the plate off the front of the ice maker by hand.
  • Locate the on/off switch for the ice maker on the front of the PC board, and turn the switch to the “Off” position.
  • Unplug the refrigerator from the electrical outlet for five minutes.

Why did my Kenmore ice maker stop working?

If the refrigerator ice maker is not working the water filter might be clogged. Try changing the water filter. If the ice maker is not working the icemaker mold thermostat might be defective. Inside the control module of the ice maker is a thermostat which monitors the temperature of the ice mold (ice tray).

How do you fix a Kenmore Elite ice maker?

Suggested clip ยท 102 seconds

HOW TO FIX A KENMORE ELITE ICE-MAKER (EASY FIX!) – YouTube

YouTube

Start of suggested clip

End of suggested clip

How do I reset my ice maker?

Look for the Reset Button

Once you do that, you should see the bright red reset button on the bottom of the ice maker itself. To reset the ice maker, push this button in and hold it for 10 seconds. You can release it sooner if: The ice maker starts making noise and operating.

What would cause ice maker to stop working?

If your ice maker isn’t producing ice at all or is producing crescents or cubes that are smaller than usual, it’s typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.

We recommend reading:  How To Fix Headphone Port?

Where is the reset button on the ice maker?

The reset button is located on the front of the ice maker, underneath the motor housing, past the front cover. Press and hold the reset button (you’ll need to apply some pressure here) until you hear the ice tray motor begin to torque, then release.

How do you troubleshoot an ice maker?

Ice Maker Does Not Make Ice

  1. 1 Make sure the bail wire above the ice tray is in the down position.
  2. 2 Check the water supply line.
  3. 3 Check the tap valve.
  4. 4 Check the solenoid.
  5. 1 Lift the bail wire to shut off the ice maker, and remove the ice bin.
  6. 2 If the problem persists, consider replacing the ice maker and valve.

What causes ice maker line to freeze?

A refrigerator ice maker that freezes up can be caused by a frozen ice maker fill tube, faulty water inlet valve, too low freezer temperature setting, or a water filter that needs replacing. First, locate the water supply to your ice maker and turn off the water supply via the shut off valve.

How do you fix a Kenmore ice maker that leaks?

0:19

8:29

Suggested clip 90 seconds

Kenmore & Whirlpool Refrigerator Repair – Leaking Water, Water

YouTube

Start of suggested clip

End of suggested clip

How do you unfreeze a Kenmore ice maker?

A more convenient option is to use a hairdryer to quickly thaw the lines.

  • Confirm first that your ice maker is not malfunctioning.
  • Wait two hours so that the water has time to freeze and dispense the ice.
  • Unplug your refrigerator to turn off the power to the ice maker.
  • Lay a towel beneath the ice maker.
We recommend reading:  How To Fix A Constantly Rebooting / Restarting Samsung Tablet?

How do I test my Kenmore ice maker?

Suggested clip 118 seconds

Ice Maker – Cycle Test – YouTube

YouTube

Start of suggested clip

End of suggested clip

How do I unclog my ice maker water line?

  1. Shut off the water valve that feeds that water-dispenser and ice-maker lines.
  2. Remove the ice bin and dump the ice out in the sink.
  3. Pour 3 to 4 cups of white distilled vinegar into the ice-maker and dispenser lines with a small funnel and allow it to soak for five to 10 minutes to break down the lime.